Home > Products > Casing Tube

DTH hammer Mission60 6 inch hammer with 6.5 inch bit

  • Brief info:DTH hammer Mission60 6 inch hammer with 6.5 inch bit, US $ 100 - 1,500 / Set, Shandong, China, WORLDRILL, DTH hammer.Source from Qingdao Worldrill Co., Ltd. on Alibaba.com.
We will reply in 24 hours.
info@miningdrillbit.com
Quick Quotation
DTH Hammer Mission60

DTH hammer Mission60 6 inch hammer with 6.5 inch bit DTH hammer, dth bit, dth hammer bit

All series of high air pressure DTH hammers and dth bits AT YOUR REQUEST

Specifications of High air pressure DTH hammers MISSION40 MISSION50 MISSION60
Model
External Diameter
Bit Shank
Hole Range
Connection Thread
Working Pressure
Bit with foot valve or not
Mission40
ø99mm
Mission40
ø110-ø135
API 2 3/8" Reg
10-25bar
No foot valve
Mission50
ø125mm
Mission50
ø135-ø155
API 2 3/8" Reg
API 3 1/2" Reg
10-25bar
No foot valve
Mission60
ø146mm
Mission60
ø155-ø203
API 3 1/2" Reg
10-25bar
No foot valve
Mission80
ø180mm
Mission80
ø195-ø254
API 4 1/2" Reg
10-25bar
No foot valve

Selecting the right hammer!

Choosing the right hammer is largely determined by hole size and type of rock formation. Ideally, the size of the hammer should match the required hole dimension as closely as possible, leaving just enough space for cuttings to evacuate the hole.

Trouble Shooting

Simple Common Methods for DTH Hammer Troubleshooting

Serial Number
Failure Content
Causes of failure
Prevention or Solution
1
It fractures in the taper thread area of the top sub.
Drill pipe thread and the top sub thread do not match with each other.
1. Check if there is burr and flash on the drill pipe thread. File the burr and the flash down.
2. Check if the drill pipe and the top sub thread are well matched with each other before connecting them.
3. Check if the drill pipe and the top sub thread can be fit closely after they are connected.
2
The external cylinder cracks.
The external cylinder is worn out excessively when normally used, and after the normal use dimension is exceeded, it fractures normally.
Check the using worn condition of the external cylinder frequently, if the normal use dimension has been exceeded (Please see the specific statement in this manual), and replace the external cylinder decisively and accordingly.
Beaten by larger external force or grinded by machines.
It is forbidden to beat the external cylinder with strong external force, such as a sledge hammer,or to be grinded by machines.
Improper torque is forced to be applied when it is disassembled or assembled.
Be sure to apply proper torque and use sharp chain tongs when it is disassembled with a chain tongs.
Welding is carried out on the external cylinder.
Welding on the external cylinder is forbidden.
3
Drive chuck fractures.
Applied torque and axial compression are much too large.
Reduce propulsion and cornering force.
The drive chuck is worn out excessively when normally used, and after the normal use dimension is exceeded, it fractures normally.
Check the using worn condition of the drive chuck frequently, if the normal use dimension has been exceeded (Please see the specific statement in this manual), and replace the drive chuck decisively and accordingly.
4
The hammer does not work.
Drill pipe thread and the top sub thread do not match with each other.
Select correct drill bit models to match the hammer model.
Internal parts are damaged.
Dissemble the hammer, examine if the spare parts are damaged including the piston, the air distributor, the internal cylinder and the guided sleeve. Purchase new spare parts to replace the old ones.
The external cylinder is deformed to become an ellipse caused by welding, burning, beating and grinded, which leads to the internal parts and the external cylinder are not concentric, as a result, the hammer sticks and fails to work.
Dissemble the hammer, examine if the spare parts are damaged including the piston, the air distributor, the internal cylinder and the guided sleeve. The external cylinder is forbidden to be welded, burned, grinded or beaten. Purchase new spare parts to replace the old ones.
Foreign material enters the inside of the hammer, the hammer sticks and fails to work.
Dissemble the hammer, clear the blockage,and clean the internal spare parts. If the internal spare parts of the hammer are worn out or damaged by the foreign material,please replace the relevant spare parts decisively to avoid further damage.
5
Pressure drop of the hammer appears.
The internal spare parts of the hammer are in lack of lubricant; under that condition, the parts rub against each other without lubricant and are damaged, thus pressure drop is caused.
Examine if there is lubricant inside the oiler. Add lubricant in time to make sure the internal spare parts of the hammer obtain full lubrication, and narrow the wear gap between parts.
The fit gap of the internal spare parts of the hammer is increased gradually because of lasting use, which leads to air leakage and pressure drop.
When each spare part is worn out and the using wear dimension of each spare part exceeds valid using dimension, changing a relevant part is recommended.
6
Drill bit falls into a well.
When assembling the drill bit into a hammer, the snap ring is missing.
Do remember to load the snap ring when assemble the drill bit.
The snap ring model is not matched with the drill bit or the hammer model.
Do select the correct snap ring model matching with the drill bit model and the hammer model.
The method or the direction of snap ring loading is incorrect.
Please install the snap ring correctly according to different models.
The snap ring is used excessively, which leads to damage or fracture.
The snap ring is easy to damage. Please replace the old ones at proper time.
7
The drill tools rotate reversely inside the hole and the drive chuck is unscrewed , which leads to the drill bit and the drive chuck falling off as a whole.
The drill tools rotate reversely inside the hole and the drive chuck is unscrewed , which leads to the drill bit and the drive chuck falling off as a whole.
The drill tools are forbidden to rotate reversely inside a hole.
The drive chuck thread is worn out.
The drive chuck thread is worn out.
The drive chuck thread is worn out. Examine the abrasion situation of the drive chuck thread. Please change a new drive chuck accordingly when the normal using size is exceeded.
8
The top sub fractures.
The top sub fractures.
Examine if the drill pipe thread and the top sub thread are matched and also fit closely when they are connected.
It rotates reversely when drilling, and the top sub is unscrewed.
It rotates reversely when drilling, and the top sub is unscrewed.
The drill tools are forbidden to rotate reversely inside a hole.
Company Introduction


Qingdao Worldrill Co., Ltd


About our Company and Products
Qingdao Worldrill Co., Ltd is one of the biggest enterprises in China specializing in research and manufacture of rock drilling products and pneumatic tools. It has a complete set of equipment for producing rock drilling products and pneumatic tools. (The key equipment is the most advanced one in the world). With its abundant experience in research and production, using the highest quality raw materials, through advanced technology and rigorous testing methods, our company has produced products with excellent performance and quality.
Our company mainly researches, designs and manufactures the following products: high pressure DTH hammers (which are the most advanced products in the field in China), all kinds of DTH bits, eccentric drilling tools for drilling with casing in the cover rocks and loose rocks, all kinds of threaded bits, RC reverse circulation hammers and bits, shank adaptors and coupling sleeves, various kinds of tool joints and drill pipes, and spare parts for drilling rigs, etc. The performance of these products is domestic leading and world first-class. The products have gained certificates including ISO 9001, API, SGS, CE, etc. "WORLDRILL" drilling tools own a good market all over China for the good quality and high performance. Meanwhile, the company is still actively exploring overseas market. "WORLDRILL" products have been exported to more than 50 countries including Australia, South Africa, Zambia, Tanzania, Korea, Malaysia, etc.

About our Product Technology and Advantages
"WORLDRILL",manufacturing drilling tools, is a leading brand in China, and the DTH Hammers without foot-valve are the most popular products in particular. Compared with the DTH Hammers of the same specification with foot-valve, the advantages of DTH Hammers without foot-valve are as follows: 1. Higher impact frequency and faster drilling speed, with the speed being 15%-20% higher than the ones with foot-valve; 2. Lower air consumption and lower oil consumption, with 10% of the oil consumption saved; 3. Avoid the trouble of foot-valve fracture and expand when heated, or the contraction when cooled; 4. Fewer internal parts, simple in structure, long in service life, and easy to assemble and disassemble. The new type hammer has been well received by users since its launch. Hammering tests have been carried out on the hardest iron ore mine in China. Compared with the products from SANDVIK and ATLAS COPCO, the new type fast hammer produced by our company is about 10% faster in terms of speed. Besides, since the thickness of the external cylinder of the hammer from our company is increased, its service life is longer than others. As to bits, the quality of products provided by our company is comparable to those from the above mentioned two companies; in the meantime, the cost performance of drilling tools branded "WORLDRILL" is much higher than those branded SANDVIK and ATLAS COPCO.

Factory and Workshop
Packing & Delivery
Our Service

1. Pre-sale service:
Act as a good adviser and assistant of clients enable them to get rich and generous returns on their investments . 1)Select equipment model. 

2)Design and manufacture products according to client's special requirement ; 

3)Train technical personnel for clients .

2. Services during the sale:
1)Pre-check and accept products ahead of delivery .
2) Help clients to draft solving plans .
3)After-sale services:
3. Provide considerate services to minimize clients' worries.
1)Complete After-sales service,professional engineers available to service machinery at home or oversea.
2) 24 hours technical support by e-mail.
3)Other essential technological service.

Related Products

Hot DTH hammer and button bits at factory price


Atlas portable air compressor


DTH forging hammer Mission50


RELATED